Unimig KUPJR55 Manuel d'instructions

1Please read and understand this instruction manual carefully before the installation and operation of this equipment.OPERATING MANUALKUPJR55© Welding

10(1) Connect the T-150 Plasma Torch to the machine. Insert the torch connection into the torch connection receptacle at the front of the machine

11Attach the male connector (torch side) to the female one(machine side). Make sure that the positioning pin aligns (A) with the corresponding notch,

12Operating Procedure for PLASMA Cutting 5) Correct amperage and travel speed are important and relevant to material thickness and are correct when sp

13● AmperageStandard rule of thumb is the thicker the material the more amperage required.On thick material, set the machine to full output and vary

14● Air pressure and volumeAir pressure, flow rate and air quality are critical to quality plasma cutting and consumable life span. The required air

15● PiercingHold the torch at an angle to the work piece, pull the trigger to start the arc and slowly rotate it to an upright position.When sparks a

16PT25C Plasma Torch & SparesPLASMA CUTTING TORCHESAir Cooled 25 Amp 202323a142226272511121212 12 12111316171a1b1c1d11b22a28292219671d453910107654

17TD35 Plasma Torch & SparesPLASMA CUTTING TORCHESAir Cooled 40 Amp T100 Plasma Torch & SparesPLASMA CUTTING TORCHESAir Cooled 100 Amp Spare

18PT25C Plasma Torch & SparesPLASMA CUTTING TORCHESAir Cooled 25 Amp T150 Plasma Torch & SparesPLASMA CUTTING TORCHESAir Cooled 150 Amp 29301c

19TD35 Plasma Torch & SparesPLASMA CUTTING TORCHESAir Cooled 40 Amp T150 Plasma Torch & SparesPLASMA CUTTING TORCHESAir Cooled 150 Amp Spare

2WARRANTY• 2 Years from date of purchase.• Welding Guns of Australia Pty Ltd Ltd warranties all goods as specified by the manufacturer of those go

20SPARE PARTS IDENTIFICATION - KUPJR55 Description Part Number 1 TOP BOARD5 B01012 10000148 B01154 100002122 CENTER BOARD B0200

21 Description Part Number 1 TOP BOARD5 B01012 10000148 B01154 100002122 CENTER BOARD B02004 100002823 BOTTOM BOARD B03004

22TROUBLE SHOOTING - KUPJR55WARNING There are extremely dangerous voltage and power levels present inside this unit. Do not attempt to diagnose or

23Welding Guns Of Australia Pty Ltd (‘Us’, ‘We’) warrants that the following products under UNI-MIG, UNI-TIG, UNI-PLAS, UNI-FLAME, TECNA, T&R, HI

24WARRANTY / RETURNS / EXCHANGESWe understand that sometimes you may need to return a product you have purchased from Welding Guns Of Australia PTY L

25WARRANTY EXCLUSIONSThis Warranty covers Material and Faulty Workmanship defects only.This Warranty does not cover damage caused by: • Normal wear a

26NOTES

27NOTES

28PO Box 3033, Lansvale NSW 2166, AUSTRALIA112 Christina Rd, Villawood, NSW 2163Phone: (02) 9780 4200Fax: (02) 9780 4244Email: [email protected]

3CONTENTS PAGEWarranty 2Safety - Pre Cautions 4-6 Air Plasma Cutting Technology 7Technical Data, Product Information 8 Machine Layout & Descr

4SAFETYIMPORTANT: BEFORE INSTALLING, OPERATING OR CARRYING OUT MAINTENANCE ON THE PLASMA CUTTER, READ THE CONTENTS OF THIS MANUAL CAREFULLY, WHICH M

5Fire hazard. Plasma cutting on closed containers, such as tanks,drums, or pipes, can cause them to explode. Flying sparks from the welding arc, hot

6CAUTION1. Working Environment.1.1 The environment in which this Plasma Cutter equipment is installed must be free of grinding dust, corrosive c

7Plasma cutters work by passing an electric arc through a gas that is passing through a constricted opening. The gas can be air, nitrogen, argon, oxy

8Razorweld • 2 Years Warranty UNIMIG WARRANTY (Power Source only)Product Code: KUPJR55Standard option includes: CUT55 Machine, T150 Plasma Torch 6

9Front & Rear Panel Layout Front Panel Layout Rear Panel Layout854321967(1) Digital Display (2) Over Current - Thermal Overload LED a. Abnorm